INSTRUCTION MANUAL
TLS-9072
Time Lapse Video Cassette Recorder
Magnétoscope time lapse à cassette
Videograbador en lapsos de tiempo
English
Français
Español
Please read this manual and accompanying “IMPORTANT SAFETY INSTRUCTIONS” sheet carefully before connecting your
VCR and operating it for the first time.
Be sure to read carefully and follow all the PRECAUTIONS on page 1.
Keep the manual in a safe place for future reference.
FEATURES
CONTENTS
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
FEATURES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ACCESSORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
œ Tape management function
œ Clog detection
œ High-speed Fast Forward/Rewind
œ Field recording/playback
LOCATIONS OF CONTROLS AND
œ 2, 12, 24, 48 and 72-hour mode recording
œ In 2, 12, 24-hour modes audio recording is available
œ Autorepeat recording
INDICATORS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ON-SCREEN MENUS . . . . . . . . . . . . . . . . . . . . . . . . . . 7
SETTING THE LANGUAGE AND CLOCK . . . . . . . . . . . 9
CHANGING THE ON-SCREEN DISPLAY . . . . . . . . . . 10
VIDEO CASSETTE TAPES . . . . . . . . . . . . . . . . . . . . . 11
TAPE MANAGEMENT FUNCTION . . . . . . . . . . . . . . . 13
NORMAL RECORDING . . . . . . . . . . . . . . . . . . . . . . . . 16
AUTOREPEAT RECORDING. . . . . . . . . . . . . . . . . . . . 19
ALARM RECORDING. . . . . . . . . . . . . . . . . . . . . . . . . . 20
PROGRAM TIMER RECORDING . . . . . . . . . . . . . . . . 23
œ Alarm recording function
œ On-screen mode setting
œ Integrated time date generator
œ Day/Time search function
œ Alarm search and Alarm scan function
œ Forward/Reverse field advance function
œ 30-day memory backup
œ Security lock
œ Recording check function
œ Automatic head cleaning function
RECORDING USING AN
ACCESSORY
EXTERNAL TIMER INPUT . . . . . . . . . . . . . . . . . . 27
NORMAL PLAYBACK. . . . . . . . . . . . . . . . . . . . . . . . . . 28
SPECIAL PLAYBACK. . . . . . . . . . . . . . . . . . . . . . . . . . 29
DAY/TIME SEARCH. . . . . . . . . . . . . . . . . . . . . . . . . . . 30
TAPE COUNTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
SETTING THE SECURITY LOCK . . . . . . . . . . . . . . . . 31
SETTING THE BUZZER. . . . . . . . . . . . . . . . . . . . . . . . 32
Power cord
CHECKING POWER FAILURE,
FAILURE DUE TO CONDENSATION AND
USAGE DURATION . . . . . . . . . . . . . . . . . . . . . . . 32
OUTPUT TERMINALS . . . . . . . . . . . . . . . . . . . . . . . . . 33
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . 37
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
2
English
LOCATIONS OF CONTROLS AND INDICATORS
Front Panel
1 23 4 5 6 7
8
9
F
GH
REC/PLAY
REV
STILL/PAUSE
STOP
FF
MENU
TIMER
]
SHIFT
«
«
l
SPEED
j
l
j
«
COUNTER
RESET MEMORY
TRACKING
– V.STILL +
PLAY
(REC CHECK)
REW
REPEAT
REC
OFF
ON SCREEN
OFF
ON
ON
ALARM
SHARPNESS
POWER
REPEAT
SPEED
DURATION
2H
20S
PROG.
CC
12H
NC
a
i
SEARCH
AUDIO ON
REC
EJECT
SOFT SHARP
MENU RESET
ALL RESET
XW
V
UTSR I Q
P
O
N
M
L
K
JI
1 TIMER button
N Digital display panel
2 MENU button
O POWER indicator
3 COUNTER RESET button
P REPEAT (autorepeat recording) indicator
4 SHIFT ], * (display position down, right) buttons
Q REC (record) button
+, * (on-screen menu cursor left, right) buttons
R REPEAT REC (autorepeat recording) switch
S ALARM DURATION (alarm recording time) switch
T ALARM SPEED (alarm recording speed) switch
U ON SCREEN switch
5 COUNTER MEMORY button
6 REC/PLAY SPEED l, j (decrease, increase
recording/playback speed mode) buttons
l, j (change the on-screen menu settings or
numerical values) buttons
V ALL RESET button
7 TRACKING/V. STILL –, + buttons
8 Cassette loading slot
9 REV (reverse playback) button
F STILL/PAUSE button
G PLAY (REC CHECK) button
H STOP button
W MENU RESET button
X SHARPNESS control
NOTE:
X Button 4 and 6 are also used for on-screen menus
setting.
In this manual, to distinguish between the functions of
each button, when giving instructions that are related to
an on-screen menu setting or operation, “press the l,
j, + or * button” will be used.
I Front door
J FF (fast forward) button
K SEARCH/AUDIO ON button
L REW (rewind) button
M EJECT button
English
3
LOCATIONS OF CONTROLS AND INDICATORS
5 Mode display
Digital Display
X Recording/playback
1
2
3
4
5
speed mode
X Alarm search mode
X Alarm scan mode
OFF
X Dew display
E
H
M
S
M
G F 9 8
7
6
X Day/Time search
1 Operation Indicators
mode
X They display the actual operation mode.
Operation Mode
Indicator
Record (REC)
Record pause (REC PAUSE)
Playback (PLAY)
6 Counter display
X Time display
Still image (STILL)
X Linear time counter
Fast forward (FF)
display
Rewind (REW)
H
M
S
Forward picture search
Reverse picture search
OFF
7 OFF indicator
Comes on when the tape end has been reached after
a recording, except during autorepeat recording mode.
Reverse playback
Field shift forward
M
8 Counter memory indicator
Field shift backward
Comes on when the counter memory function is
engaged.
X Clog detection indicator
9 Timer Recording indicator
Flashes when the recording quality deteriorates
due to dirty VCR heads.
Comes on when in timer recording stand-by mode, or
during a timer recording.
2 Cassette indicator
F Security lock indicator
Comes on when a cassette is loaded.
Flashes during thread check function.
Comes on when the security lock is engaged.
G External timer input indicator
E
Comes on when recording using the EXT TIMER IN
input terminal.
3 Alarm indicator
Flashes when an alarm is
being recorded:
Comes on after the alarm
has been recorded:
4 Power failure indicator
Comes on after a power failure.
4
English
LOCATIONS OF CONTROLS AND INDICATORS
Back Panel
9
EXT
WARNING TAPE
SW
ALARM
OUT IN
TIMER IN COM
OUT END OUT OUT
COM
PUSH
OPEN
AUDIO
VIDEO
IN
OUT
IN
OUT
REMOTE MIC IN
AC IN ~
L
K J I H G F
1 2 3 4 5 6 7 8
EXT
WARNING TAPE
SW
ALARM
OUT IN
TIMER IN COM
OUT END OUT OUT
COM
NOTE:
This terminal board
may be damaged by
0.49N·m (5kg·cm) or
more torque and using
φ6mm-tip or more size
screwdrivers.
1 EXT TIMER IN (external timer input) terminal
2 COM (common) terminal
F VIDEO OUT (video output) jack
G VIDEO IN (video input) jack
H AUDIO OUT (audio output) jack
I AUDIO IN (audio input) jack
J MIC IN (microphone input) jack
K REMOTE (remote control input) jack
L AC power input
3 WARNING OUT (warning output) terminal
4 TAPE END OUT (tape end output) terminal
5 SW OUT (switch output) terminal
6 COM (common) terminal
7 ALARM OUT (alarm output) terminal
8 ALARM IN (alarm input) terminal
9 Battery compartment
English
5
CONNECTIONS
Connect the video camera and monitor TV as shown in the figure below.
NOTE: Before making the connections, make sure the devices are disconnected from the power outlet.
Monitor TV (sold separately)
Video camera
(sold separately)
To
VIDEO IN
jack
From an external
audio source
EXT
WARNING TAPE
SW
ALARM
OUT IN
TIMER IN COM
OUT END OUT OUT
CO
PUSH
OPEN
AUDIO
VIDEO
IN OUT
IN
OUT
REMOTE MIC IN
AC IN ~
Power cord
To
VIDEO
OUT
jack
Coaxial cable
To remote control
(sold separately)
To outlet
(sold separately)
NOTES:
Power Cord Installation
X For more details, please refer to the manuals
accompanying all other devices. If the connections are
not made properly, it may cause a fire or damage the
equipment.
1 Plug the supplied power cord firmly into the AC power
input AC IN ~ socket.
2 Insert the plug of this power cord into a outlet.
X You can use a VA-RMN01 Remote Control Unit (sold
separately) to control remotely the VCR.
X The grounded power cord (3 pin plug) must be
connected to a grounded power outlet.
X If there is no video signal when the power is turned on,
“NO VIDEO” will be displayed on-screen.
6
English
ON-SCREEN MENUS
1 When no menu is displayed on-screen, press the
Types of On-screen Display and Display Sequence
MENU button.
Reference pages are shown in square brackets.
ø The (SET UP 1) menu appears.
ø Press the MENU button to save any setting
SET UP 1 menu
made and switch menu screens.
@@@@@@@<SET@UP@1>
[9, 34]
*DAYLIGHT@SET@@@@@NO@USE
@@@@@@@@WEEK@MONTH@TIME
@ON@@@1ST-SUN@@04@02:00
@OFF@@LST-SUN@@10@02:00
NOTES:
X If the (POWER FAILURE)/(DEW)/(USED TIME) menu
is displayed, pressing the MENU button will return to
the monitor screen display.
*CLOCK@SET
@01-01-00@SAT@@00:00:00
*REMOTE@@@@@@@@EJECT
*LANGUAGE-LANGUE-IDIOMA
@@@ENGLISH
X Press the MENU button to save any setting made and
switch menu screens.
SET UP 2 menu
X Press the SEARCH/AUDIO ON to save the settings
and return to the monitor screen.
@@@@@@@<SET@UP@2>
*DISPLAY
[10, 32]
X Within a menu, press the * (or +) button to move the
selection to the desired setting, then press the l (or j)
button to enter or modify the setting.
@@@DATE@@@@@@@@@@@Y
@@@TIME@@@@@@@@@@@Y
@@@ALARM@COUNT@@@@Y
@@@SPEED@@@@@@@@@@Y
*BUZZER
@@@ALARM@IN@@@@@@@Y
@@@TAPE@END@@@@@@@Y
@@@KEY@IN@@@@@@@@@N
@@@WARNING@@@@@@@@Y
* button
When a menu is displayed, press this button to move
the cursor right (or down). If the * button is pressed
when the cursor is at the right border of the screen, it
will reappear at the next position on the left of the
screen.
SET UP 3 menu
@@@@@@@<SET@UP@3>
*ALARM@MODE@@@@@@@Y1
*ALARM@DURATION@@@20S
[20, 12, 18, 33
18]
*TAPE@IN@MODE@@@@@STOP
*TAPE@END@MODE@@@@REW
*TAPE@END@OUT@@@@@-3M
*CLOG@DETECT.@@@@@Y
+ button
When a menu is displayed, press this button to move
the cursor left (or up). If the + button is pressed when
the cursor is at the left border of the screen, it will
reappear at the previous position on the right of the
screen.
SET UP 4 menu
@@@@@@@<SET@UP@4>
*SW@OUT
[33, 12, 17]
@@FIELD@@@@@@@@@01
@@TIMING@@@@@@@@FIELD
@@2H@@@@@@@@@@@@Y
*THREAD@CHECK@@@Y
*VIDEO@LOSS@@@@@N
*REC@SPEED@@@@@@N
l (or j ) button
When a setting is selected within a menu, press this
button to modify (decrease (or increase)) the setting
or the numerical value.
TAPE MANAGEMENT menu
@@@@<TAPE@MANAGEMENT>
*TAPE@MANAGE.@@@@N
*PROTECT@DAY@@@@@30
[13-15]
*REC@PASS@SET@@@@10
*GROUP@NO.@@@@@@@OFF
*OVERRIDE@@@@@@@@N
English
7
ON-SCREEN MENUS
NOTES:
X When a menu is displayed, recording will not be
possible.
X During recording or playback the menus cannot be
TIMER SET menu
displayed.
@@@@@@<TIMER@SET>
[23-27]
WEEK@START@@STOP@@@SPD
SUN@@--:--@@--:--@@---@N
MON@@--:--@@--:--@@---@N
TUE@@--:--@@--:--@@---@N
WED@@--:--@@--:--@@---@N
THU@@--:--@@--:--@@---@N
FRI@@--:--@@--:--@@---@N
SAT@@--:--@@--:--@@---@N
DLY@@--:--@@--:--@@---@N
EXT@@*****@@*****@@---@N
X To reset the settings of a menu to their original values,
select the desired menu then press the MENU RESET
button. The (USED TIME) menu data cannot be reset.
HOLIDAY SET menu
@@@@@<HOLIDAY@SET>
[25]
@@1@@-----@@@11@@-----
@@2@@-----@@@12@@-----
@@3@@-----@@@13@@-----
@@4@@-----@@@14@@-----
@@5@@-----@@@15@@-----
@@6@@-----@@@16@@-----
@@7@@-----@@@17@@-----
@@8@@-----@@@18@@-----
@@9@@-----@@@19@@-----
@10@@-----@@@20@@-----
ALARM TIME menu
@@@@@@<ALARM@TIME>
@@@@000@-----@--:--
@@@@@@@@-----@--:--
@@@@@@@@-----@--:--
@@@@@@@@-----@--:--
@@@@@@@@-----@--:--
@@@@@@@@-----@--:--
@@@@@@@@-----@--:--
@@@@@@@@-----@--:--
[21]
POWER FAILURE/DEW/USED TIME menu
@@@@<POWER@FAILURE>
[32]
000@FAILURE@@-----@--:--
@@@@RECOVERY@-----@--:--
@@@@@@@@@<DEW>
000@FAILURE@@-----@--:--
@@@@RECOVERY@-----@--:--
@@@@@@<USED@TIME>
@@@@VIDEO@@@@@@@@@00000H
@@@@POWER@@@@@@@@@00000H
8
English
SETTING THE LANGUAGE AND CLOCK
5 Press the l (or j) button to set the month the
Language Setting
English, French or Spanish can be selected by the user.
daylight saving time adjustment is made, then press
the * button.
1 Turn the power on to all devices used.
01, 02,.....11, 12 (for January,
February......November, December)
2 Press the MENU button to display the (SET UP 1)
menu.
6 Press the l (or j) button to set the time the daylight
@@@@@@@<SET@UP@1>
saving time adjustment is made.
*DAYLIGHT@SET@@@@@NO@USE
@@@@@@@@WEEK@MONTH@TIME
@ON@@@1ST-SUN@@04@02:00
@OFF@@LST-SUN@@10@02:00
7 Press the * button until “LST” of the “OFF” line is
flashing.
*CLOCK@SET
@01-01-00@SAT@@00:00:00
*REMOTE@@@@@@@@EJECT
*LANGUAGE-LANGUE-IDIOMA
@@@ENGLISH
8 Following the same procedure as above (steps 4 to
6), set when the time is changed back from daylight
saving time to standard time.
3 Press the * (or +) button, until “ENGLISH” is flashing.
9 Press the * button, until the “CLOCK SET” setting is
flashing.
4 Press the l (or j) button to select the language of
your choice.
F Press the l (or j) button to set the month (ex: 10),
then press the * button.
5 Press the SEARCH/AUDIO ON button to save the
settings.
ø The day of week is set automatically.
G Press the l (or j) button to set the day (ex: 15), then
Clock setting
press the * button.
Example: To set the clock to October 15, 2001 at 3:20
H Press the l (or j) button to set the year (ex: 01 for
PM (15:20).
2001), then press the * button.
1 Press the MENU button to display the (SET UP 1)
ø The last 2 digits only are displayed.
menu.
I Press the l (or j) button to set the hours (ex: 15 for
2 Press the l (or j) button to set the auto daylight
3 PM), then press the * button.
saving time/standard time adjustment.
J Press the l (or j) button to set the minutes (ex: 20),
NO USE. . . . No daylight saving time/standard
time adjustment is made.
then press the * button.
@@@@@@@<SET@UP@1>
*DAYLIGHT@SET@@@@@USE
@@@@@@@@WEEK@MONTH@TIME
@ON@@@1ST-SUN@@04@02:00
@OFF@@LST-SUN@@10@02:00
USE . . . . . . . The auto daylight saving time/
standard time adjustment is made.
*CLOCK@SET
3 Press the * button until “1ST” of the “ON” line is
@10-15-01@MON@@15:20:00
*REMOTE@@@@@@@@EJECT
*LANGUAGE-LANGUE-IDIOMA
@@@ENGLISH
flashing.
4 Set the day the daylight saving time adjustment is
made.
K For accurate clock setting, press the l button
together with a time broadcast, or other accurate time
signal, this will start the seconds counting from 00.
X Press the l (or j) button to set the week, then
press the * button.
1ST, 2ND, 3RD, 4TH or LST (first, second, third,
fourth or last)
L Press SEARCH/AUDIO ON button.
ø The setting procedure is now completed.
NOTES:
X Press the l (or j) button to set the day of week,
then press the * button.
X Clock display is only 24 hours.
SUN, MON, TUE, ...... SAT (Sunday, Monday,
Tuesday....Saturday)
X In STOP mode, press and hold the STOP button then
press the TRACKING/V.STILL– button to reset the
minutes and seconds to 00 (to the closest hour). For
example, between 13:30:00 and 14:29:59 the clock is
reset to 14:00:00.
X If a cassette tape is not loaded, you can reset the
seconds to “00” by pressing the COUNTER RESET
button.
English
9
CHANGING THE ON-SCREEN DISPLAY
Selecting the On-screen Display
Changing the Date/Time Display Position
You can select to display or not the date, time, the
number of alarm recordings and tape speed.
1 Turn the power on to all input devices to the VCR.
2 Set the ON SCREEN switch to the “ON” position.
ø The date and time are displayed.
1 Turn the power on to all devices used.
2 Press the MENU button until the (SET UP 2) menu is
10-15-01@MON@000
15:20:00@@@2
displayed.
@@@@@@@<SET@UP@2>
*DISPLAY
@@@DATE@@@@@@@@@@@Y
@@@TIME@@@@@@@@@@@Y
@@@ALARM@COUNT@@@@Y
@@@SPEED@@@@@@@@@@Y
*BUZZER
@@@ALARM@IN@@@@@@@Y
@@@TAPE@END@@@@@@@Y
@@@KEY@IN@@@@@@@@@N
@@@WARNING@@@@@@@@Y
3 Press the SHIFT * (or ]) button.
ø The display will move towards the right (or the
3 Press the * button, until the desired item for which
bottom).
the display function will be set is flashing.
NOTES:
4 Press the l (or j) button to set “Y” for the functions
described below.
X If the SHIFT * (or ]) button is kept pressed for 1
second or more the display will move at a faster speed.
DATE . . . . . . . . . . . . The date is displayed
TIME . . . . . . . . . . . . The time is displayed
X The display position cannot be changed while
recording.
ALARM COUNT. . . . The number of alarm
recordings is displayed
SPEED. . . . . . . . . . . The recording/playback
speed mode is displayed
5 Press the SEARCH/AUDIO ON button to save the
settings.
NOTE:
X If the ON SCREEN switch is set to the “ON” position,
the items for which “Y” is set are recorded. The items
for which “N” was set at step 4 above are not
recorded.
10
English
VIDEO CASSETTE TAPES
Use only video cassette tapes bearing the w logo. This
Loading
VCR was primarily designed for use with T-120 cassette
tapes, it is recommended to use T-120 standard grade
VHS video cassette tapes for optimal performance.
1 Place the cassette, label side up, in the loading slot.
Gently push the center of the cassette until it is
loaded automatically.
Handling Cassette Tapes
The cassette tapes should always be stored vertically, in
their cases, away from high temperatures, magnetic
fields, direct sunlight, dirt, dust and locations subject to
mold formation.
Do not tamper with the cassette mechanism and never
touch the tape with your fingers.
ø The time display will switch to the reset counter
“0H 00M 00S” display.
Protect the cassette tapes from shocks or strong
vibrations.
ø After the cassette tape is loaded, a mechanism
will operate for about 12 seconds to check that
the tape has been threaded correctly and the
cassette indicator “o” will blink during that period.
To Protect your Recordings
After having recorded a tape, if you wish to keep the
recording, use a flathead screwdriver to break off the
erasure-prevention tab on the cassette.
ø When the cassette is loaded, if the tape has
been threaded correctly, the cassette indicator
“o” will light on the digital display.
To record again on a tape without erasure-prevention tab,
cover the hole with adhesive tape.
NOTE:
X If you try to record on a cassette without
erasure-prevention tab, the VCR will eject the cassette.
Unloading
1 In stop mode, press the EJECT button.
Erasure-prevention tab
ø The cassette is automatically ejected.
NOTES:
X Do not insert any object in the cassette loading slot, as
Precautions concerning the video
cassette tapes
X Do not use tapes that are damaged, tapes that have
been cut and repaired or tapes that have been altered
in any way.
that may cause injury and damages to the VCR.
X If your hand gets stuck in the cassette loading slot,
unplug the power cord and consult the dealer where
the unit was bought. Do not forcibly pull the hand out
as that may cause severe injuries.
X Some rewinders may entangle the tape, and therefore
their use is not recommended.
X When tapes are recorded over and over again, the
recording quality will deteriorate. Refer to “Concerning
the Number of Times Tapes can be Rerecorded on” on
page 17, and replace the tape with a new tape as
required.
English
11
VIDEO CASSETTE TAPES
Correct tape thread check function
Setting the Action to Take When a
Cassette is Loaded
In the (SET UP 3) menu, you can set the mode the VCR
will go into when a cassette is loaded.
If the correct tape thread check function is on, after the
cassette tape is loaded, a mechanism will operate for
about 12 seconds to check that the tape has been
threaded (loaded) correctly and the cassette indicator “o”
will blink during that period. If the tape is not loaded
properly, the cassette will be ejected.
1 Press the MENU button until the (SET UP 3) menu is
displayed.
@@@@@@@<SET@UP@3>
*ALARM@MODE@@@@@@@Y1
*ALARM@DURATION@@@20S
NOTES:
X This function checks to make sure that the cassette
has been correctly loaded. It is recommended to use
this function to make sure the recordings are
conducted reliably.
*TAPE@IN@MODE@@@@@STOP
*TAPE@END@MODE@@@@REW
*TAPE@END@OUT@@@@@-3M
*CLOG@DETECT.@@@@@Y
X If during the tape thread check operation, the REC,
PLAY, FF, REW or STOP button is pressed, the
command will only be executed after the tape thread
has been checked. Only the EJECT button will operate
while the tape thread is being checked.
2 Press the * (or +) button, until the “TAPE IN MODE”
setting is flashing.
3 Press the l (or j) button to set the desired mode.
STOP . . . . . . Stays in stop mode
REC . . . . . . . Goes into recording mode
X If in the (SET UP 3) menu “TAPE IN MODE” is set to
“REC”, the recording indicator “m” will light during the
while the tape thread is checked. However, recording
will only start after the tape thread check is completed.
To cancel recording, press the STOP button.
4 Press the SEARCH/AUDIO ON button to save the
setting.
1 Press the MENU button until the (SET UP 4) menu is
displayed.
@@@@@@@<SET@UP@4>
*SW@OUT
@@FIELD@@@@@@@@@01
@@TIMING@@@@@@@@FIELD
@@2H@@@@@@@@@@@@Y
*THREAD@CHECK@@@Y
*VIDEO@LOSS@@@@@N
*REC@SPEED@@@@@@N
2 Press the * (or +) button, until the “THREAD
CHECK” setting is flashing.
3 Press the l (or j) button to set the desired mode.
Y . . . . . . . . . The correct tape thread check
function is on
N . . . . . . . . . The correct tape thread check
function is off
4 Press the SEARCH/AUDIO ON button to save the
setting.
12
English
TAPE MANAGEMENT FUNCTION
This VCR is equipped with a tape management function.
Using this function you can protect previous recordings
and prevent overuse of the tape by controlling the tape
protection term (number of days), the maximum number
of re-recordings of the tape and the recording group. To
use the tape management function, it must be set before
recording is started. The tape management data is
recorded at the beginning of the tape. For details on how
to set this function, refer to “Setting the Tape
If a conflict is found when the tape management data is
checked, the (TAPE MANAGEMENT) menu is displayed
and the conflicting setting will flash. This menu will show
the settings taken from the data recorded on the tape and
not the current data settings held in the VCR’s (TAPE
MANAGEMENT) menu setting. Refer to “Tape
Management Conflict Display” for detailed information.
NOTES:
Management Function”.
X During Autorepeat recording, the tape management
data at the beginning of the tape will be checked and
updated every time the tape is rewound to the
beginning. However, the “PROTECT DAY” setting will
be ignored. Also, even if there is a conflict with the
“REC PASS SET” number, autorepeat recording will
continue without any warning.
PROTECT DAY: To set the number of days before the
tape can be rerecorded over.
REC PASS SET: To limit the number of rerecordings, in
order to maintain a good image quality.
GROUP NO.: To manage tapes belonging to different
recording groups.
X If the VCR is set for alarm recordings, alarm recording
NOTE:
will be done based on the different settings.
X Before using this function, make sure that the clock is
If an alarm trigger is received while the tape is being
first rewound, the tape will continue to be rewound to
the beginning, then alarm recording will be done after
the tape has been advanced of a preset duration.
set properly.
Operation
When recording is started, the VCR will rewind the tape to
the beginning, and will playback some of the tape to
check for the presence of tape management data (no
image is displayed). While the presence and type of data
are checked, the message “T. MANAGE. CHK” is
displayed on-screen.
If an alarm trigger is received while the message “T.
MANAGE. CHK” is displayed on-screen, in order to
prevent erasing the tape management data recorded at
the beginning of the tape, the tape is advanced of a
preset duration, then alarm recording starts.
If an alarm trigger is received while tape management
data is being recorded onto the tape, alarm recording
will only start after all the data has been recorded.
NOTES:
X When a program timer recording is set, the tape
management data is checked after the TIMER button is
pressed to complete the program timer recording
setting.
Furthermore, when setting a program timer recording,
in order to protect the data, no alarm trigger will be
received until the first program timer recording starts.
X During alarm recording, the tape management function
will not operate even if it is active.
IMPORTANT NOTES:
If no tape management data is present on the
tape
X If the tape management data cannot be read, the
VCR will switch to stop mode and “INCORRECT
DATA” will be displayed on-screen.
Recording will start according to the settings in the
(TAPE MANAGEMENT) menu.
This may indicate that the beginning of the tape
(data recording/reading section) is damaged and
the tape may be unusable.
The message “INCORRECT DATA” will disappear
when the EJECT, STOP or PLAY button is pressed.
When recording starts, the updated tape
management data is recorded onto the tape.
If the tape has already been recorded on, the
message “USED TAPE” will flash on-screen until
recording starts.
X Set the security lock function to on in order to
protect the security of this feature.
If tape management data is present on the tape
The tape management data is checked and if there is
no conflict, the VCR will rewind the tape to the
beginning, then recording starts and the updated tape
management data is recorded onto the tape. While the
tape is rewound and the tape management data
recorded, the message “T. MANAGE. OK” is displayed
on-screen.
English
13
TAPE MANAGEMENT FUNCTION
NOTES:
Setting the Tape Management Function
X The data is updated at the beginning of the
recording. Even if the recording is stopped before
the end, the original data information will be
considered.
1 Press the MENU button until the (TAPE
MANAGEMENT) menu is displayed.
@@@@<TAPE@MANAGEMENT>
*TAPE@MANAGE.@@@@N
*PROTECT@DAY@@@@@30
X During Autorepeat recording, the re-recording
times count will be updated every time the tape is
rewound to the beginning. Autorepeat recording
will proceed even if the count exceeds the “REC
PASS SET” setting. If in the BUZZER section
WARNING is set to “Y”, the buzzer is heard.
*REC@PASS@SET@@@@10
*GROUP@NO.@@@@@@@OFF
*OVERRIDE@@@@@@@@N
2 Press the l (or j) button to select the desired mode.
N . . . . . . The tape management function is not
active.
7 Press the * button, until the “GROUP NO.” setting is
flashing.
Y. . . . . . . The tape management function is active.
8 Press the l (or j) button, to select the desired group
number.
When setting to “Y”, please continue with the settings
below.
OFF . . . . The group number will not be checked.
1-15 . . . . Group number setting.
3 Press the * button, until the “PROTECT DAY” setting
is flashing.
9 Press the * button, until the “OVERRIDE” setting is
4 Press the l (or j) button to select the desired
flashing.
number of days to protect the tape.
F Press the l (or j) button, to select the desired
OFF . . . . The tape is not protected.
override mode.
1-255 . . . Number of days to protect the tape
(prevent over-recording), from the date
of the last recording on the tape (or the
last expected recording date (calculated
using the tape length (T-120) and the
recording speed).
Y. . . . . . . In case of a conflict that prevents
recording, the next operation is
executed. If recording is done, then the
last recording date and the re-recording
times count are updated.
N. . . . . . . In case of a conflict that prevents
recording, the (TAPE MANAGEMENT)
menu is displayed and the conflicting
setting preventing recording will flash.
The only possible action is to press the
EJECT button, in order to eject the tape.
(Refer to “Tape Management Conflict
Display”.)
NOTES:
X Since the last expected recording date is a
calculated date (using the tape length (T-120) and
the recording speed), it may be different from the
actual last recording date, this due to other settings
such as (alarm recordings, program timer
recordings, holiday settings).
G Press the SEARCH/AUDIO ON button to save the
X When setting a program timer recording, the tape
protection term is checked when the VCR is set to
program timer recording stand-by mode.
settings.
NOTES:
X When a program timer recording is done, the data
is updated when recording starts. Even if the
recording is stopped before the programmed time,
the original data (last expected recording date) will
remain as calculated.
X Once the tape management data is recorded on
tape, it cannot be changed.
X The criteria (condition) for allowing recording will be
based on the data recorded on the tape and not the
settings in the (TAPE MANAGEMENT) menu.
5 Press the * button, until the “REC PASS SET” setting
is flashing.
6 Press the l (or j) button, to select the desired
number of re-recording times.
OFF . . . . The number of re-recording times will not
be checked.
1-100 . . . Maximum number of re-recording times.
(Refer to “Concerning the Number of Times Tapes
can be Rerecorded on” on page 17.)
14
English
TAPE MANAGEMENT FUNCTION
Tape Management Conflict Display
If when the tape management function checks the tape
data a conflict that prevents recording is found, the (TAPE
MANAGEMENT) menu is displayed with the conflicting
setting flashing and the VCR go into the stop mode. If in
the (SET UP 2) menu, in the BUZZER section WARNING
is set to “Y”, the buzzer is heard. (To stop the buzzer,
press the STOP button.)
PROTECT DAY CONFLICT
The tape is protected, the tape protection term (ex. 30
days) is not yet over.
Under LAST M/D, the date of the last recording on the
tape (or the last expected recording date (calculated
using the tape length (T-120) and the recording
speed)) is displayed.
Under NEXT M/D, the date when it will be possible to
record on the tape again is displayed.
NOTES:
X If “OVERRIDE” is set to “N” (No), the conflicting setting
is displayed flashing and the message (PRESS
EJECT) is displayed at the bottom of the screen.
Recording under these conditions is not possible.
Press the EJECT button to eject the tape. To record on
the same tape, set the OVERRIDE setting to “Y” and
modify the conflicting setting, then insert the same tape
and press the REC button. However, if only
REC PASS SET CONFLICT
The set number of recording passes has been reached.
The PASS COUNT shows the number of recording
passes on the tape (ex. since the maximum number of
recording passes is set to “10”, this prevents further
recording.)
NOTES:
“PROTECT DAY” and “REC PASS SET” are modified,
the menu will be displayed again. Press the REC
button one more time to start recording. Recording
starts and the tape data is updated.
X When conducting Autorepeat recording, if the PASS
COUNT exceeds 100, “101*” will be displayed
flashing.
X If using a tape recorded previously on a different
type of VCR (no tape data), when the set number of
recordings is exceeded, “USED” will flash next to the
PASS COUNT number.
Conflict display sample
@@@@<TAPE@MANAGEMENT>
*TAPE@MANAGE.@@@@N
*PROTECT@DAY@@@@@30
@LAST@M/D@@@@@@NEXT@M/D
@@@@@10/15@@@@@@@@@11/15
*REC@PASS@SET@@@@10
@PASS@COUNT@@@@@@10
*GROUP@NO.@@@@@@@7
@[email protected].@@@@@@8
*OVERRIDE@@@@@@@@N
@@@@@@(PRESS@EJECT)
GROUP NO. CONFLICT
The group numbers do not match.
The REC GR. NO. shows the tape recording group
number (ex. this tape belongs to a different recording
group number 8 than the one set 7.)
X If the “OVERRIDE” is set to “Y” (Yes), the (TAPE
MANAGEMENT) menu is displayed and conflicting
setting preventing recording will flash and VCR go into
the stop mode.
To enter the record mode, press the REC button.
English
15
NORMAL RECORDING
Normal Recording
[Recording Speed Mode]
Recording
Maximum
recording
Recording
interval
Before starting
speed mode
Audio recording Tape motion
(hour mode) duration (hours) (second)
X Turn the power on to all devices used.
2
12
24
48
72
2
14
26
50
74
1/60
7/60
13/60
25/60
37/60
Possible
Continuous
Intermittent
X Load a cassette tape with erasure-prevention tab.
NOTE:
Not possible
X If in the (SET UP 3) menu, TAPE IN MODE is set
to “REC”, recording will start after the tape thread
has been checked.
Record Pause
Recording can be interrupted temporarily.
X Set the ON SCREEN switch to the “ON” position.
1 Press the STILL/PAUSE button during recording.
ø The Pause/Still indicator “N” blinks.
1 Press the REC/PLAY SPEED l (or j) button to set
the recording speed mode.
NOTES:
ø The recording speed mode is displayed
X The image appears on-screen but it is not recorded.
on-screen and on the digital display.
X If a recording pause continues for 5 minutes or
more, the VCR will go into stop mode to avoid
damaging the tape.
2 Press the REC button.
ø The record indicator “m” light.
ø Recording starts.
2 To resume recording, press the REC button, or press
the STILL/PAUSE button again.
ø If the tape end is reached while recording, “OFF”
is displayed on the digital display and the unit
goes into the mode set at the “TAPE END
MODE” line in the (SET UP 3) menu.
NOTES:
X If in the (SET UP 2) menu, in the BUZZER section
TAPE END is set to “Y”, the buzzer will be heard
as long as “OFF” is displayed on the digital display.
X To cancel the “OFF” display, press the STOP,
EJECT, FF, REW or PLAY button.
3 To stop recording, press the STOP button.
NOTES:
X A tape recording made on this VCR may not play back
with the same degree of clarity on a time lapse from
another manufacturer.
X If you press on the REC button and the loaded
cassette has no erasure-prevention tab, the VCR will
eject the cassette.
16
English
NORMAL RECORDING
Concerning the Number of Times Tapes
can be Rerecorded on
Changes to the Recording Speed Mode
During Recording
Depending on the recording speed mode, the tape must
be replaced after a certain number of recording times.
It is possible to permit or prevent changing the recording
speed mode during recording.
Refer to the table below for the maximum number of times
a tape can be recorded on.
1 Press the MENU button until the (SET UP 4) menu is
displayed.
@@@@@@@<SET@UP@4>
*SW@OUT
Recording speed mode
(hour mode)
Maximum number of
recording times
(with a standard grade
tape)
@@FIELD@@@@@@@@@01
@@TIMING@@@@@@@@FIELD
@@2H@@@@@@@@@@@@Y
*THREAD@CHECK@@@Y
*VIDEO@LOSS@@@@@N
*REC@SPEED@@@@@@N
2
100
50
50
25
15
12
24
48
72
2 Press the * (or +) button, until the “REC SPEED”
setting is flashing.
3 Press the l (or j) button to set the desired mode.
Y. . . . . . . . . . Recording speed mode can be
changed
NOTES:
N . . . . . . . . . Recording speed mode can not be
changed
X The maximum number of recording times will vary
depending on the location and kind of tape used. Verify
the recording quality and replace the tape when the
quality starts to deteriorate.
4 Press the SEARCH/AUDIO ON button to save the
setting.
The maximum number of recording times indicated
above are based on test tapes (T-120) used by the
company.
Action to Take when the Video Signal
Deteriorates
X If using longer tapes (i.e. T-160) the tape travel will not
If there is no video signal during recording or when a
menu is not displayed (in stop, fast forward or rewind
modes), “VIDEO LOSS” can be displayed on-screen and
a signal (0 V) can be output at the ALARM OUT terminal.
If in the (SET UP 2) menu, in the BUZZER section
WARNING is set to “Y”, the buzzer will be heard. To stop
the buzzer, press the STOP button.
be as stable and that may cause problems.
1 Press the MENU button until the (SET UP 4) menu is
displayed.
2 Press the * (or +) button, until the “VIDEO LOSS”
setting is flashing.
3 Press the l (or j) button to set the desired mode.
N . . . . . . . . . The video loss warning is not active.
Y. . . . . . . . . . The video loss warning is active.
4 Press the SEARCH/AUDIO ON button to save the
setting.
English
17
NORMAL RECORDING
Recording Check
Setting the Mode at the End of the Tape
The image being recorded can be checked.
In the (SET UP 3) menu, you can set the mode of the
VCR mode when the tape reaches the end during
recording.
1 During recording, press the PLAY (REC CHECK)
button.
1 Press the MENU button until the (SET UP 3) menu is
ø The tape will be rewound and then played back.
The VCR will then return to the previous
recording mode.
displayed.
@@@@@@@<SET@UP@3>
*ALARM@MODE@@@@@@@Y1
*ALARM@DURATION@@@20S
NOTE:
*TAPE@IN@MODE@@@@@STOP
*TAPE@END@MODE@@@@REW
*TAPE@END@OUT@@@@@-3M
*CLOG@DETECT.@@@@@Y
X During recording check operations, recording is
suspended momentarily.
Clog Detection
2 Press the * (or +) button, until the “TAPE END
This VCR is equipped with a clog detection function.
MODE” setting is flashing.
The recording quality is monitored automatically. When
the heads are dirty and the recording quality deteriorates,
the output at the WARNING OUT terminal becomes 0V
(Low), the “m” indicator flashes on the digital display, and
the buzzer sounds.
3 Press the l (or j) button to set the desired mode.
X Setting when the REPEAT REC switch is set to the
“OFF” position.
REW. . . . . . . Rewinds the tape to the beginning,
then goes to stop mode
If in the (SET UP 3) menu, CLOG DETECT. is set to “N”,
the recording quality is not monitored.
STOP . . . . . . Goes to stop mode
EJECT . . . . . The cassette is ejected
NOTES:
X Setting when the REPEAT REC switch is set to the
X To cancel the “m” indicator display and reset the
WARNING OUT terminal output, press the STOP
button.
“ON” position.
R1. . . . . . . . . Autorepeat recording mode is
automatically canceled if there was
an alarm trigger
X Clog detection is not possible if recording in 2-hour
mode.
R2. . . . . . . . . Autorepeat recording mode is
active even if there was an alarm
trigger
4 Press the SEARCH/AUDIO ON button to save the
setting.
18
English
AUTOREPEAT RECORDING
NOTES:
Autorepeat Recording
X If during autorepeat recording there is an alarm trigger,
The same tape can be recorded over many times.
“AL” is displayed on the digital display and alarm
recording will take place. (Please refer to page 20,
“ALARM RECORDING”.)
X Follow the Before starting steps, under “NORMAL
RECORDING”.
1 Set the REPEAT REC switch to the “ON” position.
X If the “TAPE END MODE” setting is R 1, the REPEAT
indicator will go off if there is an alarm trigger. After
alarm recording, the recording will continue to the end
of the tape then it will be rewound to the beginning and
stop. “OFF” will be displayed on the digital display. To
turn off the buzzer (if in the (SETUP 2) menu, in the
BUZZER section TAPE END is set to “Y”) and the
“OFF” display, press the STOP, EJECT, FF, REW or
PLAY button.
ø The REPEAT indicator will light.
2 Press the MENU button until the (SET UP 3) menu is
displayed.
ø The “ALARM MODE” setting is flashing.
@@@@@@@<SET@UP@3>
*ALARM@MODE@@@@@@@Y1
*ALARM@DURATION@@@20S
*TAPE@IN@MODE@@@@@STOP
*TAPE@END@MODE@@@@R1
*TAPE@END@OUT@@@@@-3M
*CLOG@DETECT.@@@@@Y
X If “AL” is displayed on the digital display and the “TAPE
END MODE” setting is R1, autorepeat recording is not
possible.
3 Press the * (or +) button, until the “TAPE END
MODE” setting is flashing.
4 Press the l (or j) button to set to “R 1” or “R 2”.
(Please refer to page 18, “Setting the Mode at the
End of the Tape.”)
5 Press the SEARCH/AUDIO ON button to save the
setting.
6 Press the REC/PLAY SPEED l (or j) button to set
the recording speed mode.
7 Press the REC button.
ø Recording will start. When the tape end is
reached, the VCR will rewind it to the beginning,
and recording will resume.
ø When the end of the tape is reached, a buzzer
will be heard (if in the (SETUP 2) menu, in the
BUZZER section TAPE END is set to “Y”) and
“OFF” will be displayed until the rewinding
operation starts.
English
19
ALARM RECORDING
By connecting the ALARM IN terminal to a door switch,
an interphone, etc., a recording can be done only when
necessary.
If the ALARM DURATION switch is set to the “PROG.”
position, please continue with steps 5 and 6.
5 Press the * button, until the “ALARM DURATION”
setting is flashing.
Alarm Recording Setting
Alarm recording is performed when there is an input
(trigger) at the ALARM IN terminal, “AL” is displayed on
the digital display.
6 Press the l (or j) button, to select the desired alarm
recording duration (20S, 40S, 1M, 2M, 3M, 4M, 5M,
or CC).
20S-5M. . Recording only for the displayed duration
X Make all necessary connections.
CC . . . . . Recording as long as the alarm signal is
being input (minimum 5 seconds)
X The alarm triggers are received while in recording and
stop modes.
7 Press the SEARCH/AUDIO ON button to save the
settings.
X Follow the Before starting steps, under “NORMAL
RECORDING”.
NOTES:
1 Set the ALARM SPEED switch to the desired
X During alarm recording all buttons are disabled.
recording speed.
X If “OFF” is displayed on the digital display, alarm
recording is not possible in order to prevent the
recorded tape to be recorded over.
2H . . . . . 2-hour mode recording
12H . . . . 12-hour mode recording
NC . . . . . Recording at the speed already set
To cancel the “OFF” display, press the STOP, EJECT,
FF, REW or PLAY button.
2 Set the ALARM DURATION switch to the desired
recording duration.
X If an alarm trigger is received while alarm recording is
in progress, recording duration for the second alarm
will be calculated from that point. The alarm counter will
register the alarm, but it will not be found during an
alarm scan and alarm search.
20S. . . . . 20-second recording
PROG. . . Recording for the duration set for the
“ALARM DURATION” item in the (SET
UP 3) menu.
X If there is a power failure during alarm recording, and
the power is restored within the recording set duration,
alarm recording will continue.
CC . . . . . Recording as long as the alarm signal is
being input (minimum 5 seconds)
3 Press the MENU button until the (SET UP 3) menu is
X If the alarm recording duration is short, the alarms may
not be found during an alarm scan or an alarm search.
If the alarms are going to be reviewed using alarm
scan or alarm search, then in 2-hour mode, 20-second
or more recording duration should be used.
displayed.
@@@@@@@<SET@UP@3>
*ALARM@MODE@@@@@@@Y1
*ALARM@DURATION@@@20S
*TAPE@IN@MODE@@@@@STOP
*TAPE@END@MODE@@@@REW
*TAPE@END@OUT@@@@@-3M
*CLOG@DETECT.@@@@@Y
4 Press the l (or j) button to set the desired alarm mode.
Y1. . . . . . Alarm recording is done when there is an
alarm trigger.
Y2. . . . . . Alarm recording is done only when there
is an alarm trigger during programmed
timer recording.
Y3. . . . . . Alarm recording is done only if there is
an alarm trigger and the VCR is not in
programmed timer recording mode.
Y4. . . . . . Alarm recording is done only when there
is an alarm trigger during programmed
timer recording duration. Timer recording
is not possible.
N . . . . . . Alarm recording is not performed even if
there is an alarm trigger.
20
English
ALARM RECORDING
Alarm Recording Counter Display
Checking the Alarm Recordings Time
X During alarm recording, “AL” will be flashing on the
1 Press the MENU button until the (ALARM TIME)
digital display.
menu is displayed.
X If the ON SCREEN switch is set to the “ON” position,
ø The number of alarm recordings, and the 8 most
the number of alarms will flash on the monitor screen.
recent alarm recording times are displayed.
X The maximum display number of alarm recordings is
“999”, at the next alarm recording the counter will
indicate “000”.
@@@@@@<ALARM@TIME>
@@@@008@12-25@19:00
@@@@@@@@11-25@23:00
@@@@@@@@11-25@15:00
@@@@@@@@10-25@08:00
@@@@@@@@10-25@06:00
@@@@@@@@09-25@20:00
@@@@@@@@09-25@16:35
@@@@@@@@09-25@10:52
X When the (ALARM TIME) menu is displayed, press the
MENU RESET button to reset the alarm counter to
“000” (all the data of the (ALARM TIME) menu is reset).
NOTE:
Connections to the ALARM IN/OUT
Terminals
X The data for the previous alarm recordings is
erased.
X Alarm input signal
2 Press the SEARCH/AUDIO ON button, the normal
Connect a make-contact (no voltage) switch between
the ALARM IN and COM terminals.
screen is displayed.
NOTE:
X Alarm output signal
Normally DC 5V are output between the ALARM OUT
and the COM terminals. When an alarm input (trigger)
is received and the unit is recording, the output falls to
0V. Once the alarm recording is over, the output
returns to DC 5V.
X If the MENU RESET button is pressed while the
(ALARM TIME) menu is displayed, the displayed data
is erased. “AL” will be erased from the digital display.
English
21
ALARM RECORDING
Alarm Scan
Alarm Search
To look for an alarm recording by viewing the first 5
seconds of each alarm recording.
To go to the beginning of a desired alarm recording.
1 Press the SEARCH/AUDIO ON button during stop
1 Press the SEARCH/AUDIO ON button twice during
mode.
stop mode.
ø “AL SEARCH 01” will be displayed on screen.
ø “AL SCAN” will be displayed on screen.
2 Press the REC/PLAY SPEED l (or j) button to set
the desired alarm number (1 to 99), then press the FF
(or REW) button.
2 Press the FF (or REW) button.
ø The unit will advance (or rewind) the tape at high
speed and playback the first 5 seconds of every
alarm recording.
ø The desired alarm is searched and a still image
of the beginning of the alarm recording will
appear on-screen.
ø To cancel the alarm scan mode, press the STOP
button.
NOTE:
3 While the desired recording is being played back,
X The alarm number is relative to the actual tape
press the PLAY button.
position. (Please refer to the illustration below.)
ø Playback will start, alarm scan mode is cancelled.
Playback
1
1
2
Alarm number 2
Alarm trigger input point
Rewind direction
Fast-forward direction
Actual position
3 Press the PLAY button.
ø Playback will start.
22
English
PROGRAM TIMER RECORDING
There are two program timer recording methods, daily
recording or recording on certain days of the week.
7 Press the l (or j) button to set the recording stop
minutes (ex: 00), then press the * button.
ø The “SPD” (recording speed) position will start
flashing.
Example 1: To record on every Saturday from 9:00
AM to 5:00 PM (17:00), in 24-hour
mode (recording speed).
NOTE:
X If the set stop time is earlier than or the same time
as the set start time, the VCR will consider the stop
time to be the following day, and “T” will be
displayed next to the recording stop time.
X Follow the Before starting steps, under “NORMAL
RECORDING”.
1 Press the MENU button until the (TIMER SET) menu
is displayed.
8 Press the l (or j) button to select the recording
X “SUN” (Sunday) will be flashing.
speed mode (ex: 24), then press the * button.
@@@@@@<TIMER@SET>
WEEK@START@@STOP@@@SPD
SUN@@--:--@@--:--@@---@N
MON@@--:--@@--:--@@---@N
TUE@@--:--@@--:--@@---@N
WED@@--:--@@--:--@@---@N
THU@@--:--@@--:--@@---@N
FRI@@--:--@@--:--@@---@N
SAT@@--:--@@--:--@@---@N
DLY@@--:--@@--:--@@---@N
EXT@@*****@@*****@@---@N
ø “N” will start flashing.
9 Press the l (or j) button to select the desired
program timer recording mode.
Y. . . . . . . . . . recording will take place
N . . . . . . . . . recording will not take place
@@@@@@<TIMER@SET>
2 Press the * (or +) button, until “SAT” (Saturday) is
WEEK@START@@STOP@@@SPD
SUN@@--:--@@--:--@@---@N
MON@@--:--@@--:--@@---@N
TUE@@--:--@@--:--@@---@N
WED@@--:--@@--:--@@---@N
THU@@--:--@@--:--@@---@N
FRI@@--:--@@--:--@@---@N
SAT@@09:00@@17:00@@@24@Y
DLY@@--:--@@--:--@@---@N
EXT@@*****@@*****@@---@N
flashing.
3 Press the * button.
ø The recording start hour position starts flashing.
4 Press the l (or j) button to set the recording start
hour (ex: 09), then press the * button.
ø Repeat steps 2 to 9 to program timer
recordings for other days of the week.
ø The recording start minutes position starts
flashing.
F Press the SEARCH/AUDIO ON button to save the
5 Press the l (or j) button to set the recording start
settings.
minutes (ex: 00), then press the * button.
G Press the TIMER button.
ø The recording stop hour position starts flashing.
ø The timer recording indicator “n” will light on the
digital display, the VCR is now in timer recording
stand-by mode.
6 Press the l (or j) button to set the recording stop
hour (ex: 17), then press the * button.
ø The recording stop minutes position starts
flashing.
NOTES:
X To modify, cancel or stop timer recording, press
the TIMER button to cancel the timer recording
mode.
X To record everyday at the same time, at step 2
select the “DLY” line.
English
23
PROGRAM TIMER RECORDING
A timer recording of more than 24 hours can only be set
on the 7th (SAT) and 8th (DLY) lines of the (TIMER SET)
menu.
8 Press the l (or j) button to set the desired stop day
of the week (ex: MON), then press the * button.
ø The recording stop hour position starts flashing.
9 Press the l (or j) button to set the recording stop
Example 2: To record every week from Saturday at
9:00 PM (21:00) to Monday at 7:00 AM, in
48-hour mode (recording speed).
hour (ex: 07), then press the * button.
ø The recording stop minutes position starts
flashing.
F Press the l (or j) button to set the recording stop
X Follow the Before starting steps, under “NORMAL
minutes (ex: 00), then press the * button.
RECORDING”.
ø The “SPD” (recording speed) position will start
1 Press the MENU button until the (TIMER SET) menu
flashing.
is displayed.
G Press the l (or j) button to select the recording
X “SUN” (Sunday) will be flashing.
speed mode (ex: 48), then press the * button.
2 Press the * (or +) button, until “SAT” is flashing.
ø “N” will start flashing.
3 Press the l (or j) button to set the desired start day
H Press the l (or j) button to select “Y”.
of the week (ex: SAT), then press the * button.
@@@@@@<TIMER@SET>
ø The recording start hour position starts flashing.
WEEK@START@@STOP@@@SPD
SUN@@--:--@@--:--@@---@N
MON@@--:--@@--:--@@---@N
TUE@@--:--@@--:--@@---@N
WED@@--:--@@--:--@@---@N
THU@@--:--@@--:--@@---@N
FRI@@--:--@@--:--@@---@N
SAT@@21:00@@**:**@@***@*
MON@@**:**@@07:00@@@48@Y
EXT@@*****@@*****@@---@N
4 Press the l (or j) button to set the recording start
hour (ex: 21), then press the * button.
ø The recording start minutes position starts
flashing.
5 Press the l (or j) button to set the recording start
I Follow steps F and G under “PROGRAM TIMER
minutes (ex: 00), then press the * button.
RECORDING” on page 23.
ø The recording stop hour position starts flashing.
6 Press the l (or j) button to set “**” for the
recording stop hour.
ø The rest of the line settings will change to
“**:** *** *”, the day of the next line will
change to the next day and the start time will
change to “**:**” automatically.
7 Press the * button.
ø The day of the week of the 8th line is flashing.
24
English
PROGRAM TIMER RECORDING
Setting the Holidays
Changing a Program Timer Recording
By setting the holidays, timer recording will be conducted
on those days, as set for Sundays.
1 Press the MENU button until the (TIMER SET) menu
is displayed.
1 Press the MENU button until the (HOLIDAY SET)
2 Press the * (or +) button until the setting to correct is
menu is displayed.
flashing.
3 Press the l (or j) button to correct the setting.
@@@@@<HOLIDAY@SET>
@@1@@-----@@@11@@-----
@@2@@-----@@@12@@-----
@@3@@-----@@@13@@-----
@@4@@-----@@@14@@-----
@@5@@-----@@@15@@-----
@@6@@-----@@@16@@-----
@@7@@-----@@@17@@-----
@@8@@-----@@@18@@-----
@@9@@-----@@@19@@-----
@10@@-----@@@20@@-----
4 Press the SEARCH/AUDIO ON button to save the
settings.
5 Press the TIMER button.
To Cancel a Program Timer Recording
1 Press the MENU button until the (TIMER SET) menu
2 Press the l (or j) button to set the month of the
holiday, then press the * button.
is displayed.
3 Press the l (or j) button to set the day of the holiday.
4 Press the * button.
2 Press the * (or +) button until the “Y” corresponding
to the timer recording to cancel is flashing.
ø Repeat steps 2 to 4 to set up to 20 holidays.
3 Press the l (or j) button to select “N”.
5 Press the SEARCH/AUDIO ON button to save the
4 Press the SEARCH/AUDIO ON button to save the
settings.
settings.
5 Press the TIMER button.
NOTE:
X If setting holidays, be sure that a timer recording is set
To Cancel all Program Timer Recordings
for Sunday. If not, this function will not operate.
1 Press the MENU button until the (TIMER SET) menu
X If a timer recording for Sundays is entered, the holidays
timer recording will not function if the program timer
recording mode is set to “N”.
is displayed.
2 Press the MENU RESET button.
ø All programmed timer recordings are erased.
X To erase a setting, follow the same procedure as
above, but at step 2 and 3, enter “--” instead of a
setting.
3 Press the SEARCH/AUDIO ON button, the normal
screen is displayed.
English
25
PROGRAM TIMER RECORDING
NOTES:
X During timer recording or timer recording stand-by, all
the buttons on the VCR, except the TIMER button and
the buttons to set/cancel the security lock (see page
31), are disabled.
X If the power fails, the recording will be interrupted.
When the power is restored, the recording will resume
if the stop time has not yet been reached, and “P” will
be displayed on the digital display. The VCR internal
battery is completely recharged after the VCR has
been connected to a live outlet for 48 hours, and it will
maintain all the VCR settings memory for up to 30 days.
X Set the timer recordings so that the recording times do
not overlap. If they do, the one with the earliest
recording start time will have priority. (See chart below.)
7:00PM
8:00PM
9:00PM
10:00PM
Program 1
Program 2
Program 3
These portions will
not be recorded
X To set two or more timer recordings for a same day of
the week, press the * (or +) button, until the day of the
week for the second recording is flashing, then press
the l (or j) button, to set the desired day of the week.
X If no timer recording is set or a cassette without
erasure-prevention tab is loaded, when the TIMER
button is pressed the timer recording indicator “n” will
start flashing and a buzzer will be heard.
X If “OFF” is displayed on the digital display, timer
recording is not possible in order to prevent the
recorded tape to be recorded over.
26
English
RECORDING USING AN EXTERNAL TIMER
INPUT
Recording can be controlled by an external start/stop
5 Follow steps F and G under “PROGRAM TIMER
signal input at the EXT TIMER IN terminal.
RECORDING on page 23”.
ø When an external signal is input, “E” will light on
the digital display and recording will take place.
Example 3: To record using the signal input at the
EXT TIMER IN terminal, in 24-hour
mode.
NOTES:
X Other timer recordings using the standard procedure
X Follow the Before starting steps, under “NORMAL
can also be programmed.
RECORDING”.
X The external input signal must be input at the EXT
NOTE:
TIMER IN terminal.
X External timer input recording can only be set on the
9th line (EXT) of the (TIMER SET) menu.
1 Press the MENU button until the (TIMER SET) menu
is displayed.
2 Press the * (or +) button, until the “SPD” (recording
speed) position of the “EXT” line starts flashing.
3 Press the l (or j) button to select the recording
speed mode (ex: 24), then press the * button.
ø “N” will start flashing.
4 Press the l (or j) button to select “Y”.
@@@@@@<TIMER@SET>
WEEK@START@@STOP@@@SPD
SUN@@--:--@@--:--@@---@N
MON@@--:--@@--:--@@---@N
TUE@@--:--@@--:--@@---@N
WED@@--:--@@--:--@@---@N
THU@@--:--@@--:--@@---@N
FRI@@--:--@@--:--@@---@N
SAT@@--:--@@--:--@@---@N
DLY@@--:--@@--:--@@---@N
EXT@@*****@@*****@@@24@Y
English
27
NORMAL PLAYBACK
Normal Playback
Tracking Control
1 Turn on the power to the VCR and TV monitor.
If there is noise in the image during playback,
2 Load the video cassette tape.
1 While looking at the playback picture, press and hold
the TRACKING/V. STILL+ button to minimize the
noise.
3 Press the REC/PLAY SPEED l (or j) button to
select the playback speed mode.
2 If it cannot be minimized, press the TRACKING/V.
ø The selected playback speed mode is displayed
STILL– button.
on the digital display.
NOTE:
Vertical Lock Control
During still image mode,
X A slow motion effect or accelerated playback effect
can be achieved by using a slower or faster
1 Press and hold the TRACKING/V. STILL+ button to
playback speed than the speed used for recording.
reduce the vertical rolling of the image.
4 Press the PLAY button.
2 If it cannot be corrected, press the TRACKING/V.
ø Playback starts.
STILL– button.
ø If necessary, adjust the tracking to eliminate the
noise from the picture.
Sharpness Control
Turn the SHARPNESS control clockwise or
counterclockwise for the desired sharpness of the image.
ø If the image is unstable (rolling vertically), adjust
the vertical lock control to correct.
5 To stop playback, press the STOP button.
ø To advance or rewind the tape, press the FF or
Audio Playback
X Audio playback is only possible in 2-hour, 12-hour and
REW button.
24-hour modes.
NOTES:
X The playback speed has to be the same as the
X If a tape recorded in SP mode on a standard VCR is
recording speed, for normal playback of the audio.
loaded, playback will be done in 2-hour mode.
X For a tape recorded in 12-hour and 24-hour recording
modes, to playback the audio, press the
X A tape recorded on a time lapse VCR produced by
another manufacturer may not play back with the same
degree of clarity on this unit.
SEARCH/AUDIO ON button after pressing the PLAY
button. “?” will be displayed to the left of the playback
speed on the digital display.
NOTE:
X Noise will appear in the image when audio playback is
used in 12- or 24-hour modes.
28
English
SPECIAL PLAYBACK
Picture Search (Forward and Reverse)
Reverse Playback
1 Press the FF (or REW) button, during normal
1 Press and hold the REV button, during normal
playback.
playback.
ø The image can be seen while the tape is
ø Reverse playback will start.
advanced (or rewound) at high speed.
2 To return to normal playback, release the REV button.
2 To return to normal playback, press the PLAY button.
NOTES:
NOTES:
X During reverse playback, noise will appear in the
X During picture search, noise (horizontal bars) will
picture.
appear in the picture.
X Reverse playback is only possible during 2-hour
X The sound is muted.
playback speed mode.
X The sound is muted.
Still Image
1 Press the STILL/PAUSE button, during normal
playback.
ø A still image can be viewed.
2 To return to normal playback, press the PLAY button.
NOTES:
X If still mode continues for 5 minutes or more, the VCR
will go into stop mode to avoid damaging the tape.
X If the image is unstable (rolling vertically), adjust the
vertical lock control to correct.
Field Advance
1 Press the FF (or REW) button, during still image
mode.
ø The still image is advanced (or rewound) of one
image (field).
2 To return to normal playback, press the PLAY button.
NOTES:
X During reverse field advance, noise will appear in the
picture.
X If field advance mode continues for 5 minutes or more,
the VCR will go into stop mode to avoid damaging the
tape.
English
29
DAY/TIME SEARCH
Day/Time Search
NOTES:
X If during a search the end of the tape is reached, the
tape will rewind and stop. If the beginning of the tape is
reached, it will stop.
1 Press the SEARCH button three times during stop
mode.
ø “T/D SEARCH 01 00:00” will be displayed on
X The alarm and day/time data are recorded on the tape
in a similar format. If they overlap, the alarm data will
have the priority. Therefore, when searching for a
day/time when an alarm recording was done, the
day/time search will not stop at the desired location. In
such a case, use alarm scan to find the desired
recording location.
screen.
1H22M33S
T/D@SEARCH
01@@00:00
DAY@TIME
X The day/time search function may not operate correctly
2 Press the REC/PLAY SPEED l (or j) button to set
if searching for a timer recording time.
the desired day, then press the * button.
X If a recording on a tape extends for over a one month
period, the same day may be present twice on the
tape. If such a day is searched, since there is no month
search setting, the desired day may not be found.
3 Press the REC/PLAY SPEED l (or j) button to set
the desired hour, then press the * button.
4 Press the REC/PLAY SPEED l (or j) button to set
the desired minutes.
NOTES:
X The setting can be made in 10 minutes increments
only.
X For recordings made on other VCRs, the exact
time may not be found even if the minutes are
entered. For tapes recorded on older models of
VCRs produced by this company (the ones without
a minutes setting for the day/time search function),
make sure to set the minutes to “00”.
5 Press the FF (or REW) button.
ø The desired day/time is searched and a still
image of the recording will appear on-screen.
6 Press the PLAY button.
ø Playback will start.
30
English
TAPE COUNTER
Using the counter, it is easy to find a desired recording.
NOTES:
1 Press the COUNTER RESET button, at the beginning
X There is no tape counter indication for the blank
of the desired recording.
portions of the tape.
ø The counter will be reset to “0H 00M 00S”.
2 Press the COUNTER MEMORY button.
ø “[” is displayed on the digital display.
X In the 2-hour recording speed mode only, the tape
counter indicates real hours, minutes and seconds.
X In the other recording speed modes, the tape counter
indication is a ratio of the 2-hour mode base indication.
(In 12-hour recording mode, each “second” of the tape
counter actually represents approximately 12/2 + 1 = 7
real seconds.)
ø To cancel the counter memory function, press
the COUNTER MEMORY button a second time.
3 After recording or playback, press the REW button
from stop mode.
X There may be a slight discrepancy between the
position shown on the tape counter and the actual tape
position.
ø The tape is rewound to the counter “0H 00M 00S”
reading.
ø If you rewind the tape past the “0H 00M 00S”
X When rewinding the tape past the “0 00 00 ”
H
M
S
position, press the FF button.
position, a minus (–) sign will be displayed.
SETTING THE SECURITY LOCK
The security lock function is designed to prevent
accidental stopping of recording if the STOP button is
pressed inadvertently.
NOTES:
X While the security lock is engaged all commands,
except the one to cancel the security lock, are disabled.
1 While holding the SHIFT * button, press the
X The security lock cannot be engaged while a menu is
REC/PLAY SPEED j button.
displayed.
ø “x” is displayed on the digital display.
To cancel the security lock, while holding the SHIFT
* button, press the REC/PLAY SPEED l button, “x”
will be erased from the digital display.
English
31
SETTING THE BUZZER
A buzzer can be set to sound during alarm recording, if
during recording the tape reaches the end, if buttons are
pressed or if there is a mechanical failure that causes the
tape to stop or be ejected, etc.
TAPE END . . The buzzer will be heard when the
end of the tape is reached during
recording. To stop the buzzer,
press the STOP, EJECT, FF, REW
or PLAY button.
1 Press the MENU button until the (SET UP 2) menu is
displayed.
KEY IN . . . . . The buzzer will be heard when one
of the VCR buttons is pressed.
@@@@@@@<SET@UP@2>
*DISPLAY
WARNING . . The buzzer will be heard if the
heads are dirty and recording
qualtiy deteriorate, or if the tape
stops or is ejected due to a
@@@DATE@@@@@@@@@@@Y
@@@TIME@@@@@@@@@@@Y
@@@ALARM@COUNT@@@@Y
@@@SPEED@@@@@@@@@@Y
*BUZZER
@@@ALARM@IN@@@@@@@Y
@@@TAPE@END@@@@@@@Y
@@@KEY@IN@@@@@@@@@N
@@@WARNING@@@@@@@@Y
problem with the internal
mechanism. To stop the buzzer,
press the STOP button.
2 Press the * (or +) button, until the desired item for
which the buzzer function will be set is flashing.
4 Press the SEARCH/AUDIO ON button to save the
3 Press the l (or j) button to set “Y” for the functions
setting.
described below.
NOTES:
ALARM IN . . The buzzer will be heard during
alarm recording.
X If “N” is set, the buzzer will not be heard.
X During timer recording mode, security lock engaged
mode and alarm recording mode, the buzzer will not be
heard when a button related to one of these modes is
pressed, even if “Y” is set for the “KEY IN” item.
CHECKING POWER FAILURE, FAILURE DUE TO
CONDENSATION AND USAGE DURATION
1 Press the MENU button until the (POWER FAILURE),
Example
(DEW) and (USED TIME) menu is displayed.
@@@@<POWER@FAILURE>
002@FAILURE@@12-25@07:15
@@@@RECOVERY@12-25@07:30
(POWER FAILURE). . . The number of power
failures, and the date and
time of the most recent
@@@@@@@@@<DEW>
001@FAILURE@@12-25@11:00
@@@@RECOVERY@12-25@12:00
power failure and recovery
are displayed.
@@@@@@<USED@TIME>
@@@@VIDEO@@@@@@@@@@00003H
@@@@POWER@@@@@@@@@@00007H
(DEW) . . . . . . . . . . . . . The number of failures due
to condensation, and the
2 Press the SEARCH/AUDIO ON button, the normal
screen is displayed.
date and time of the most
recent failure and recovery
are displayed.
NOTE:
X If the MENU RESET button is pressed while the
(POWER FAILURE) and (DEW) menu is displayed, the
data is erased. The (USED TIME) data cannot be reset.
“@” will be erased from the digital display.
(USED TIME). . . . . . . . The video heads usage
duration and the power on
duration are displayed.
32
English
OUTPUTTERMINALS
TAPE END OUT Terminal
SW OUT Terminal
X During recording, when the end of the tape is reached
or when the tape counter reading indicates 1 hours 57
minutes or more, the output becomes 0V (Low).
When recording, a pulse signal is output at the SW OUT
terminal.
This terminal is usually connected to the switch input (SW
IN) of devices like a camera switcher unit, or a quad
compressor.
X To reset the output, press the STOP or EJECT button.
X During autorepeat recording, when the end of the tape
is reached, the output becomes 0V (Low) for about 2
seconds only.
FIELD : 16.7 msec.
FRAME : 5 msec.
5V (H)
Tape end or 1H57M00S
Output reset
(Output impedance: 5.7 kΩ)
0V (L)
5V (H)
SW OUT Terminal Output Setting
(Output impedance: 5.7 kΩ)
1 Press the MENU button until the (SET UP 4) menu is
0V (L)
displayed.
TAPE END OUT Terminal Output Setting
ø The FIELD (or FRAME) setting is flashing.
1 Press the MENU button until the (SET UP 3) menu is
@@@@@@@<SET@UP@4>
*SW@OUT
displayed.
@@FIELD@@@@@@@@@01
@@TIMING@@@@@@@@FIELD
@@2H@@@@@@@@@@@@Y
*THREAD@CHECK@@@Y
*VIDEO@LOSS@@@@@N
*REC@SPEED@@@@@@N
@@@@@@@<SET@UP@3>
*ALARM@MODE@@@@@@@Y1
*ALARM@DURATION@@@20S
*TAPE@IN@MODE@@@@@STOP
*TAPE@END@MODE@@@@REW
*TAPE@END@OUT@@@@@-3M
*CLOG@DETECT.@@@@@Y
NOTE:
X If “TIMING” is set to FRAME (see step 4),
2 Press the * (or +) button, until the “TAPE END OUT”
“FRAME” will be indicated instead of “FIELD”.
setting is flashing.
2 Press the l (or j) button to set the desired pulse
3 Press the l (or j) button, to select the desired
signal interval.
output mode.
Available settings are:
–3M . . . . . . . The output becomes 0 V (Low)
when the tape counter reaches
FIELD. . . . . . 01, 02, 03, 04, 05, 10, 30 or 60 field
FRAME . . . . 01, 02, 03, 04, 05, 10, 30 or 60 frame
“1 57 00 ” and/or when the tape
H
M
S
reaches the end.
3 Press the * button, until the “TIMING” setting is
END . . . . . . . The output becomes 0 V (Low)
when the tape reaches the end.
flashing.
4 Press the l (or j) button to set “FIELD” or “FRAME”.
4 Press the SEARCH/AUDIO ON button to save the
FIELD. . . . . . 1 pulse is output after each set
number of fields.
setting.
FRAME . . . . 1 pulse is output after each set
number of frames.
5 Press the * button, until the “2H” setting is flashing.
6 Press the l (or j) button to set the desired “2H”
mode.
Y. . . . . . . . . . When recording in 2-hour mode, a
pulse signal is output.
N . . . . . . . . . When recording in 2-hour mode, a
pulse signal is not output.
7 Press the SEARCH/AUDIO ON button to save the
settings.
English
33
OUTPUTTERMINALS
REMOTE Jack
You can use a VA-RMN01 Remote Control Unit (sold
separately) to control remotely the VCR.
Remote control setting
The remote control switch 7 can be set to either eject the
tape or access the menus.
1 Press the MENU button until the (SET UP 1) menu is
NOTE:
displayed.
X The functions not available on the VCR will not operate.
@@@@@@@<SET@UP@1>
*DAYLIGHT@SET@@@@@USE
@@@@@@@@WEEK@MONTH@TIME
@ON@@@1ST-SUN@@04@02:00
@OFF@@LST-SUN@@10@02:00
Remote control of the VCR is possible by connecting a
remote controller with a circuit such as indicated below, to
the REMOTE jack.
*CLOCK@SET
@10-15-01@MON@@15:20:00
*REMOTE@@@@@@@@EJECT
*LANGUAGE-LANGUE-IDIOMA
@@@ENGLISH
NOTES:
X Use a 3.5 mm mini-jack type plug.
2 Press the * (or +) button, until the “REMOTE” setting
X The connection should be done using a shielded cable
is flashing.
no more than 5 meters long.
3 Press the l (or j) button to select the desired switch
X The functions not available on the VCR will not operate.
mode.
EJECT . . . . . Switch 7 will eject the tape.
MENU. . . . . . Switch 7 will display the menu.
Remote control circuit
4 Press the SEARCH/AUDIO ON button to save the
R0 1.2K
setting.
SW0: EJECT
R1 0.3K
WARNING OUT Terminal
SW1: STOP
X If the tape stops or other problem, the output becomes
R2 0.43K
SW2: STILL/PAUSE
0V (Low).
X To reset the output, press the STOP or ALL RESET
R3 0.51K
SW3: REW
button or unplug the power cord then plug it back in.
R4 0.62K
SW4: FF
Tape movement stop
Output reset
R5 0.75K
SW5: PLAY
5V (H)
(Output impedance: 5.7 kΩ)
R6 0.91K
0V (L)
SW6: REC
R7 1.1K
SW7: EJECT (or MENU)
NOTE:
X If the output is 0V (Low) due to the clog detect function,
R8 1.3K
SW8: REV
it can be reset by simply pressing the STOP button.
R9 2.0K
SW9: REC/PLAY SPEED j, j
COM Terminal
X Common GND (ground) terminal when connecting
R10 2.4K
SW10: REC/PLAY SPEED l, l
other terminals to external devices.
R11 3.6K
SW11: SHIFT ], »
R12 5.6K
SW12: SHIFT «, «
The resistance tolerance is
2% or less.
34
English
MAINTENANCE
Daily Inspection
Periodic Inspection
The following daily inspections are recommended in order
to assure long-term and trouble-free operation of the unit.
Periodic inspection and maintenance should be referred
to your dealer.
The daily inspections are particularly important if using
autorepeat recording.
If there is noise in the playback picture, and it cannot be
corrected using the tracking control, it may indicated that
the video heads need cleaning.
Inspection Procedure
1 Turn on the power to the VCR, camera, TV monitor
The video heads should be inspected every 1,000 hours
of use to determine if they need to be replaced.
The video heads usage can be checked using the (USED
TIME) menu.
and other connected devices.
2 Check that the image received on the TV monitor is
correct.
Cabinet Cleaning
3 Check that the on-screen display of the date and time
is correct.
Clean the outside of the cabinet with a clean, soft cloth,
moistened with lukewarm water and wrung dry.
4 To check the recording condition of the previous day,
rewind the recorded tape a few seconds.
DO NOT USE SOLVENTS OR OTHER TYPES OF
CLEANERS. THESE CHEMICALS CAN CRACK OR
DISCOLOR THE CABINET.
5 Press the PLAY button and check that the playback
image is correct.
6 Check that the recorded date and time are correct.
NOTES:
About the Backup Battery
X If the security lock is engaged, it has to be released
The date and time settings are maintained for up to 30
days by a rechargeable lithium battery that is fully
charged after the VCR has been connected to a power
source for 48 hours or more.
before proceeding to the inspection.
X If any problem is discovered during the inspection,
unplug the power cord then consult your dealer.
Depending on the battery usage it may become
necessary to change it. For replacement and disposal of
the old battery, please contact your dealer.
After the battery has been replaced, press the ALL
RESET button, then enter all the time, date, etc. settings
as required.
English
35
MAINTENANCE
Maintaining and Checking The Mechanism
To maintain the VCR functions and features working properly, and to avoid damages or dirt on the tape, it is
recommended to follow the maintenance points and periodicity indicated below.
For detailed information, please contact your dealer.
Maintenance Table
PARTS
Tape Path System ASSY, BRAKE BAND
ASSY, LEVER BT (tape guide)
F : Cleaning
E : Confirmation
8000H
k
v : Lubrication
k : Change
2000H
4000H
6000H
NOTES
E
F
F
E
F
F
F
F
F
k
F
F
k
F
F
F
F
k
E
F
F
E
F
F
F
F
F
F
FULL ERASE HEAD
k
ASSY, ROLLER CLEANER
ASSY, GUIDE ROLLER
ASSY, MOUNTING INCLNE S
ASSY, MOUNTING INCLNE T
ACE HEAD
ASSY, LEVER PINCH ROLLER
MOUNTING, LIFT PINCH
CAM, LIFT PINCH
k
F
k
k
k
k
k
k
GEAR, CAM PINCH
k
ASSY, EARTH CYL
COMPL, CYLINDER
ASSY, CYLINDER UPPER
k
F(k)
F(k)
Fv
Fv
v
k
F
F(k)
Fv
Fv
v
F
F(k)
Fv
Fv
v
F(k)
F(k)
Fv
Fv
v
v
v
E
Reel Drive System ASSY, REEL SUPPLY
ASSY, REEL TAKEUP
GEAR, REEL S
GEAR, REEL T
v
v
v
PULLEY, REEL
v
v
v
SPECIAL, WASHER 2.4 X 6 X 0.25
COMPL, MOUNTING CLUTCH
BELT, REEL
MOTOR, CAPSTAN
ASSY, GEAR FRICTION
ASSY, BRAKE S
E
v
E
F
v
E
E
E
k
v
k
k
k
E(k)
vk
E
E(k)
v
k
vk
E
Brake
E
ASSY, BRAKE T
E
E
E
ASSY, BRAKE CAPSTAN
ASSY, BRAKE SOFT T
ASSY, LOADING MOTOR
DAMPER
E
E
E
E
k
Loading Drive
System
E
k
k
COMPL, GEAR WORM
CAM, MAIN
SPECIAL WASHER 3.6 X 0.5
GEAR, WHEEL 1
E
E
k
k
k
k
GEAR, WHEEL 2
MODE SWITCH
E
E
E
E
E
E
E
E
E
E
E
k
k
SLIDE, CRECENT
GEAR, LOAD S
GEAR, RACK FRONT
GEAR, RACK START
GEAR, PINON
BACK TENSION TORQUE
FWD, REW TORQUE
PLAY TORQUE
k
k
k
k
k
Performance
Check
E
E
E
E
E
E
E
E
E
PB BACK TENSION TORQUE 25~50g⋅cm
FWD, REW TORQUE ≥ 600g⋅cm
PLAY 55 ~ 110g⋅cm
E
E
REV TORQUE
E
REV 100 ~ 210g⋅cm
NOTES:
1. This table shows the maintenance for up to 8000 hours. After this, repeat from the start or the table.
2. For places with symbols such as E (k) and F (k), carry out checking and cleaning, and replace if necessary.
3. This periodic maintenance check table changes considerably according to the using conditions and environment.
4. Refer to (USED TIME) menu for the length of time the unit has been used.
5. As life may be shortened if foreign particles and dusts remain accumulated on the tape guides and rotating and contacting portions, clean if dirty.
6. Dusts and other foreign particles on the tape guides may also shorten the tape life and lower picture quality, therefore clean thoroughly.
36
English
TROUBLESHOOTING GUIDE
If the unit does not operate normally when you follow the instructions indicated in the manual, please refer to the table
below.
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
No power
The power cord is not connected
The connections are not correct
Connect the power cord
No image displayed on
the monitor TV
Check that all connections are correct
The power to the camera and/or monitor TV Turn all connected devices power on
is not turned on
The buttons do not
respond
A cassette tape is not loaded
Load a cassette and turn the power on
All functions are suspended due to
condensation
Wait for the “4” indicator to go off
Alarm recording
Wait for the alarm recording to end
Cancel the security lock
The security lock is engaged
Recording is not
possible (the tape is
ejected)
The loaded cassette has no
erasure-prevention tab
Load a cassette tape with
erasure-prevention tab or cover the tab hole
with adhesive tape
Autorepeat recording is
not possible
“AL” is displayed on the digital display
Display (ALARM TIME) menu, then press
the MENU RESET button to turn off the “AL”
indicator
Timer recording is not
possible
The date and time are not set correctly
Set the date and time correctly
The unit is not set to timer recording
stand-by mode
Press the TIMER button to display “n” on
the digital display
“N” is selected for the timer recordings
“OFF” is displayed on the digital display
The video heads need cleaning
Be sure to select “Y” for the programmed
timer recordings
Alarm recording is not
possible
Press the EJECT, STOP, FF, REW or
PLAY button to turn the indicator off
Noise in the playback
picture
Clean the video heads
The date and time are
not recorded
The ON SCREEN switch is set to the “OFF” Set the ON SCREEN switch to the “ON”
position
position
The cassette tape
cannot be ejected
Problem with the system
Unplug the power cord then plug it back in
The cassette is ejected
a few seconds after it
has been inserted
The tape is not threaded correctly
Try inserting the cassette one more time or
using a new cassette. If it is ejected again,
please consult your dealer.
After a Power Failure
System Down
If after a power failure the recording speed is reset to
2-hour mode, it is due to insufficient backup battery
charge. This is not a malfunction.
If the unit does not function at all, try the following.
1 Unplug the power cord then plug it back in.
2 Reset the memory. (Press the ALL RESET button.
Under normal conditions, do not touch the ALL
RESET button.)
NOTE:
X The time and date will be reset, and the security
lock will be cancelled.
3 If the problem is not corrected after performing steps
1 and 2 a few times, consult your dealer.
English
37
SPECIFICATIONS
General Specifications
Video heads system
Dual-azimuth 4-head rotating helical scanning system:
Dual azimuth 2-head for record and standard playback
Dual azimuth 4-head for forward picture search, reverse picture search
and still mode
Audio recording
Tape speed
In 2-, 12- and 24-hour modes
33.35 mm /sec (2-hour mode)
Specified video cassette tape
Recording/playback time
Fast forward/rewind time
Television system
VHS 1/2 inch video cassette tape
2, 12, 24, 48 and 72 hours (when using T-120 tape)
approximately 2 minutes 45 seconds (when using T-120 tape)
NTSC color TV system
Video
Recording method
Luminance signal: FM recording
Chrominance signal: Down-converted direct recording
Video input
Video output
Horizontal resolution
1 V(p-p), BNC, 75 Ω, unbalanced
1 V(p-p), BNC, 75 Ω, unbalanced
Black & white mode
Color mode
350 line or more
300 line or more
Audio
Input
Output
Microphone input
–8 dBs, RCA pin jack, 27 kΩ, unbalanced
–8 dBs, RCA pin jack, 600 Ω, unbalanced
–60 dBs, 3.5 mm mini jack, 10 kΩ, unbalanced
Connectors
Alarm input
Alarm output
Switch output
Tape end output
Warning output
Ext timer input
Common
Low level active (0V 100msec or more)
DC 5 V (±0.5)/5.7 kΩ, Low at alarm
DC 5 V (±0.5)/5.7 kΩ, Low at switching
DC 5 V (±0.5)/5.7 kΩ, Low at tape end
DC 5 V (±0.5)/5.7 kΩ, Low at warning
Low level active (0V 100msec or more)
0 V (GND)
Remote control input
3.5 mm mini jack
Other Specifications
Operating temperature range
Operating humidity range
Power requirements
Power consumption
Dimensions
5°C to 40°C
80% or less
120 V AC, 60 Hz
17 W
420 (W) x 99.5 (H) x 295.5 (D) mm
approximately 4.4 kg
Weight
NOTE: The specifications and external appearance of this unit are subject to change without notice.
38
English
SANYO INDUSTRIAL
VCR WARRANTY
OBLIGATIONS
In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s expense,
unless specifically stated otherwise in this warranty. The names and addresses of Authorized Sanyo Service Centers may be obtained by calling the
toll-free number listed below.
For product operation, authorized service center referral, service assistance or problem resolution, call
CUSTOMER INFORMATION 1-800-421-5013
Weekdays 8:30 AM – 5:00 PM Pacific Time
For accessories and/or parts, call
PARTS ORDER INFORMATION 1-800-726-9662
Weekdays 8:30 AM – 5:00 PM Pacific Time
THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES OF AMERICA, EXCLUDING ALL
U.S. TERRITORIES AND PROTECTORATES. THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL PURCHASER OR END-USER. THE
ORIGINAL DATED BILL OF SALE, SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE
CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED.
Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO Fisher Company warrants this SANYO product against defects in materials
and workmanship for the periods specified below. SFC will repair or replace (at its option) the product and any of its parts which fail to conform to this
warranty. The warranty period commences on the date the product was first purchased or rented at retail.
LABOR
1 YEAR
PARTS
1 YEAR
VIDEO HEADS
90 DAYS
EXCLUSIONS
This warranty does not cover (A) the adjustment of customer-operated controls as explained in the appropriate model’s instruction manual, or (B) the
repair of any product whose serial number has been altered, defaced or removed.
This warranty shall not apply to the cabinet or cosmetic parts, batteries or routine maintenance.
This warranty does not apply to uncrating, setup, installation, removal of the product for repair or reinstallation of the product after repair.
This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including, but not limited to, any
malfunction, defect or failure caused by or resulting from unauthorized service or parts, improper maintenance, operation contrary to furnished
instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse, neglect, accident, incorrect power line voltage, fire, flood
or other Acts of God, or normal wear and tear.
The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any other
obligation or liability.
SFC DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED, WITH REGARD TO THIS PRODUCT (INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS). IN NO EVENT SHALL SFC BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING FROM THE OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER
THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL. SFC’S LIABILITY FOR ANY AND ALL LOSSES AND DAMAGES RESULTING
FROM ANY CAUSE WHATSOEVER, ARISING OUT OF OR IN CONNECTION WITH THE SALE, USE OR OWNERSHIP OF THIS PRODUCT
INCLUDING WARRANTOR’S NEGLIGENCE, ALLEGED DAMAGED OR DEFECTIIVE GOODS, WHETHER SUCH DEFECTS ARE DISCOVERABLE
OR LATENT, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
ATTENTION
For your protection in the event of theft or loss of this product, please fill in the information below for you own personal records.
Model No. ________________________________________________
Date of Purchase __________________________________________
Serial No. ________________________________________________
(Located on back or bottom side of unit.)
Purchase Price ___________________________________________
Where Purchased _______________________________________________________________________________________________________
English
39
1AC6P1P2341– –B
RC4Q/NA 2
SANYO Electric Co., Ltd.
(0601KP-01)
Issue No. 3
Copyright SANYO, 2000 All rights reserved.
Printed in Japan
|